Search Stories by: 
&/or
 

Load & Haul













Right sizing the hauler fleet with intelligent tools

Size does matter when it comes to determining if your fleet is keeping up with the changing conditions of your jobsite. Eric Yeomans explains why site simulation software is the perfect tool for ensuring your fleet is appropriately sized for the task at hand.

In any extractive operation, an articulated hauler is only as effective as its supporting machines, such as excavators and loaders. Evolving site conditions can also factor into proper fleet sizing. What once was the perfect combination of machines may not be in the future as haul routes change.

Thus, properly sizing a hauler requires looking at the site and the fleet holistically, and continuing to monitor fleet utilisation over time. Fortunately, many equipment dealers and OEMs offer a range of technologies and services that can make this an easier process than ever before.

Site simulation

One of the best ways to gain a holistic view of the operation is to conduct an analysis via site simulation software — a process typically completed with the help of an equipment dealer and/or OEM. The process begins by gathering all necessary data points on jobsite conditions.

The following summary will outline, step by step, actual data from a site simulation conducted by Volvo Construction Equipment and a local dealer for a Virginia limestone quarry owner that was evaluating whether four 60-tonne articulated haulers (Volvo A60Hs) would pose efficiencies over five 43-tonne articulated haulers (Volvo A40Gs).

Table 1. Job-site specific factors that are inputted into the simulation software.
Table 1. Job-site specific factors that are inputted into the simulation software.

Step 1: Jobsite conditions

The first step is completed with the help of a handheld GPS device that records and logs site information along the haul route, including haul distances, curves in the haul road and road gradients — factors that all affect cycle times. This data is then imported as a GPX file into site simulation software.In the example below, the haul route is 2.2km from loading point to dumping site.

Once GPS data is imported, the fleet manager works hand in hand with the OEM or dealer to input a number of jobsite-specific factors, including material information, such as bank density, swell factor, loose density and the estimated average percentage of bucket fill (see Table 1 above). The software also allows for selecting from several categories of ground conditions to calculate rolling resistance of the equipment — a key factor in estimating cycle times and fuel efficiency levels.

Step 2: Operating hours

Next, annual working hours (per machine) are estimated by taking into consideration total scheduled shifts per year and average shift duration (minus non-operating delay per shift), and then subtracting estimated scheduled maintenance. In this instance, the quarry owner estimated 95 per cent machine availability, which amounts to 240 eight-hour shifts (or 1824 operating hours) per machine, per year.

Step 3: Equipment specifications

"One of the best ways to gain a holistic view of the operation is to conduct an analysis via site simulation software"

After incorporating GPS information and manually entering jobsite factors, the team then inputs equipment model information, including number of machines, model numbers and bucket size(s). The software will automatically pull the necessary equipment specifications to run a production simulation.

The team can then run reports with various combinations of equipment models for the loading and hauling units, comparing them side-by-side to arrive at the solution that delivers the best production at the lowest operating cost.

Step 4: Production analysis review

The final production analysis includes data points such as average cycle time, average bucket passes to fill the hauler, estimated average fuel consumption per hour, and ultimately, a comprehensive fleet analysis outlining fleet production per year in cubic metres.

Machine utilisation can be further reviewed in a cycle time breakdown, outlining exactly how the hauler is spending time during each cycle, including average load queue time, average spot time at the loading unit, average travel time, average spot time at dump and average dumping time.

For the Virginia quarry owner, the simulation surprisingly showed cycle times slightly shorter with the A60Hs (nine minutes, 19 seconds) versus the A45Gs (nine minutes, 32 seconds) due to less travel time. In addition, each haul resulted in 9.2 per cent more material, which meant fewer cycles and lower fuel consumption, despite the A60s having a larger engine.

Site simulations can account for factors that affect cycle times, eg haul distances, road curves and gradients.
Site simulations can account for factors that affect cycle times, eg haul distances, road curves and gradients.

The site simulation analysis also shows a difference in fuel consumption for the loader (a Volvo L350F with 7m3 bucket) between the two scenarios, burning more fuel in litres per operating hour when loading five A40s versus loading four A60s.

Looking at the important figures for fuel consumption, number of machines, total operating hours and production levels, the team can evaluate cost to operate (including labour and fuel consumption) versus production levels. In the Virginia scenario, a fleet comprised of four A60s versus five A40s resulted in estimated savings of 25.6 per cent in operating costs.

Step 5: Cost to operate

These figures represent only a part of the picture of total operating cost, however. The dealer or OEM should also work hand in hand with the customer to determine total cost of ownership based on a proposed purchase agreement and/or financing structure for both scenarios.

Other costs to consider include: depreciation schedule, taxes, insurance, estimated resale value, service plans, tyre replacements and maintenance costs.

The results of a cost analysis as in-depth as that available with site simulations will help fleet managers determine if they need more machines or could benefit from a different size or even type of machine based on all the information provided.

Once arriving at the most efficient scenario and moving ahead with the recommended fleet structure, it’s important to continue monitoring utilisation, as haul routes and tasks change with an evolving jobsite.

This can be done by once again leveraging the expertise of the equipment dealer and OEM to monitor machine utilisation via telematics, and also making use of the haulers’ on-board weighing data to spot any potential inefficiencies.

Intelligence = Profit

With so much real time data at your fingertips — and OEMs continuing to provide more optimal size classes that open up new opportunities — spending some time to right-size your fleet may be one of the best decisions you make for your operation’s bottom line.











ABOUT THE AUTHOR
Eric Yeomans

Eric Yeomans is Volvo Construction Equipment’s product manager for GPPE products.









Tuesday, 23 October, 2018 10:07am
login to my account
Username: Password:
Free Sign Up

Receive FREE newsletter and alerts


CONNECT WITH US
standardlarge_0418
advertisement
standardlarge_0218
advertisement
standardlarge_0118
advertisement